RSS FeedCategories
- Antarctic (192)
- Articles About RYM (13)
- Delivery stories (32)
- Life stories (71)
- Moutaineering – Aconcaqua, Island Peak (40)
- Personal Travel (106)
- Projects (26)
- Race Reports (150)
- Safety at Sea (19)
- South Georgia (314)
- Tips and tricks (51)
Archives
- September 2016
- February 2016
- September 2015
- February 2014
- December 2013
- November 2013
- October 2013
- June 2013
- May 2013
- April 2013
- February 2013
- January 2013
- December 2012
- November 2012
- October 2012
- September 2012
- August 2012
- July 2012
- June 2012
- May 2012
- April 2012
- March 2012
- February 2012
- January 2012
- December 2011
- November 2011
- October 2011
- September 2011
- August 2011
- July 2011
- June 2011
- May 2011
- April 2011
- March 2011
- February 2011
- January 2011
- December 2010
- November 2010
- October 2010
- September 2010
- August 2010
- July 2010
- June 2010
- May 2010
- April 2010
- March 2010
- February 2010
- January 2010
- December 2009
- November 2009
- October 2009
- September 2009
- August 2009
- July 2009
- June 2009
- May 2009
- April 2009
- March 2009
- February 2009
- January 2009
- December 2008
- November 2008
- October 2008
- September 2008
- August 2008
- July 2008
- June 2008
- May 2008
- April 2008
- March 2008
- February 2008
- January 2008
- December 2007
- November 2007
- October 2007
- September 2007
- August 2007
- July 2007
- June 2007
- May 2007
- February 2007
- January 2007
- September 2006
- August 2006
- July 2006
- June 2006
- May 2006
- March 2006
- June 2005
- May 2005
- February 2005
- January 2005
- December 2004
- June 2004
- September 2003
- August 2003
- June 2003
- October 2002
- March 2002
- February 2002
- September 2001
- August 2001
- April 2001
- August 2000
- July 2000
- November 1998
- July 1998
- June 1998
- August 1996
- 0
Three bridge fiasco
It has been a while I know. Anyways last weekend I took the moore 24 out for the second time since 2009 and did the three bridge fiasco. There were over 300 boats out there. I drove the start and Matt took the helm at blackhaller as it was easier for me to run around doing the deck work. It was the first time Matt had sailed in three years and I need to learn how to sail my boat again that is for sure. Normally the wind dies on this race and I am the furthest away from the finish line going around in circles however we saw up to 20 knots and finished early afternoon which is unheard of. Guess I didn’t need all that petrol for the outboard. See below for a timelapse taken
New crankshaft gasket
The crankshaft gasket has been leaking oil it would have been an easy job except for one bolt which I couldn’t get out without removing the pulleys.
A little bit of anaerobic gasket sealant.
What’s behind the cover on a 300HP engine!
A new gasket. However, as with all jobs on this boat more jobs are created everytime I do one I find another three to do! When I removed the pullies I found the alternator adjuster which allows the belts to be tightened is fully seized up. Despite PB blaster, hammering it and lots of heat and cold shock it is still well siezed. Time for cracking the nuts or a hacksaw.
More fun with pumps…
Pretty much all the pumps in the engine room were pouring out salt water so I have had to order new mechnical seals. The seals have be arriving from Italy, UK, Florida, Mexico and distributors in CA. It would seem to be an easy job except most of the bolts are well seized and have required heat, impact drivers and PB blaster!
Rusted internals of the freezer compressor pump.
Time for some new pump mounts.
Rusted pump shaft.
Fun at TMMC with grandma and grandpa
Learning about how to rescue a marine mammal with grandma.
In the carriers like a seal…
Unfortunately all the seals that were better had already been released back into the wild to be home for the holidays.
Fun with the kids in the snow
The girls check out the huge icicles at Boreal.
I think Charlie likes the syrup quite a bit.
Snow angels are the best part of snow.
Beautiful sunset following us up the hill to Tahoe.
Little planks for little people. Henry would not get off the slopes.
Batteries
Liquid electrolyte Roll batteries each weighs 350lbs. To get them out of the boat they covers were take off and each cell unbolted divided into three.
The batteries had been overheating for a while and the old captain had disconnected the ones that were in the worst shape. The electroyte had cystallised leaving a causic residue in the bilges.
The new clean sealed AGMs. Lighter, less dangerous and with more power.
Crystals removed from the battery boxes. Thirty batteries in total were changed out which took a day.
Mammal Rescue
I was on call for the Marine Mammal Center last week. There are not normally many calls at this time of year so I helped out loading four sea lions to be released at Chimney Rock. One was a big guy and the others small.
I got one call to go an assess a sea lion at Kirby Cove. which was quite lethargic and malnurished. I will have to get to know what sea lions normally act like as they are different to furries.
I hung out at the beach which had a beautiful view of SF while two people came down from the center and two other rescue volunteers. We wheeled the cage down to the beach. The stranding intern had the net and ran in to attempt to capture it however, a big wave came in and took out Ben who was boarding in an attempt to stop her from making her way into the surf. I was also in the surf so got a little damp but not as damp as Ben got.
A beautiful view of Rodeo Beach from the Marine Mammal Center.
Compass
What’s wrong with this picture? Think about how you would steer. The way to fix it was to remove the compass from the console turn it upside down and shake it till the card flips the right way then put it back in. Much easier to steer now!
Impellors
The engine driven bilge pumps clutch wasn’t engaging and the wheel was moving around quite a bit so time for a full service.
One impellor puller later…
The impellor was in quite a state with damage to the blades so a new one is on order along with a few gaskets and some other parts and pieces.
This shows why you want to use fresh water to test the pump or flush it through after emptying a bilge that has salt water in it. The impellor has left a ‘footprint’ in hard salt deposits.